No hay artículos en el carro
No hay artículos en el carroDescripción del producto
1. En la interfaz de operación, gire el codificador para ajustar la velocidad, tecla CW -- rotación hacia adelante, tecla CCW -- rotación inversa, tecla RUN/STOP -- salida de parada de operación.
2. Mantén pulsado el codificador para ingresar a la configuración del menú.
1. En la interfaz de configuración del menú, gira el codificador para ajustar y cambiar los códigos de parámetro F-01~F-13.
2. Mantén presionado el codificador, guarda los parámetros y salga para entrar en la interfaz de operación.
1. En la interfaz de configuración del menú, presione brevemente el codificador para ingresar el estado de configuración de parámetros del menú correspondiente F-XX, el parámetro parpadea y luego presione brevemente Shift para girar el codificador para ajustar el parámetro.
2. Presione brevemente la tecla RUN/STOP para salir del parámetro y volver a la interfaz de ajuste de números del menú principal.
John
Comentado en los Estados Unidos el 3 de marzo de 2025
Easy and simple unit for controlling a Nema17/23 stepper motor. This unit is only a controller and not a motor Driver. I'm using it with the TB6600 motor driver which was easy to setup. I wanted a controller that was easy to set up, had a fairly good range of control options and did not require programming a microcontroller such as an Arduino. Note: This unit can be used with an Arduino as it has a UART.
Electronics Engineer
Comentado en los Estados Unidos el 2 de mayo de 2024
These are robust little modules that do almost anything that I would like to do with a small stepper motor. Very configurable for speed, steps, etc. Much simpler and cheaper than an arduino lashup. Used one to with a geared stepper to drive the long axis of my metal lathe as a power feed. Easily configured to get the speed and feed required. Very cost effective and final product looks good.
Omm@r
Comentado en México el 1 de febrero de 2024
Funciona de maravilla, mejor que otros modelos similares
Dave Z
Comentado en los Estados Unidos el 5 de enero de 2024
I used this with the EASON CNC Stepper Motor Driver DM556 (https://www.amazon.com/dp/B08RHLDZD5?psc=1&ref=ppx_yo2ov_dt_b_product_details) and a stepper motor I had in my stock of motors. It worked great and was easy to setup and use. The real bonus is that the device has a ttl serial interface that uses Modbus RTU so you can set any of the 13 parameters remotely (see my answer by searching "serial" in the Q&A section). Be sure to use a ttl-to-RS232 adapter like this one: https://www.amazon.com/dp/B00LPK0Z9A?psc=1&ref=ppx_yo2ov_dt_b_product_detailsI have several home automation projects in mind for this device but have not decided which one to do first. I will post an updated review once I have a project completed.
Mike Someone
Comentado en los Estados Unidos el 15 de julio de 2023
I t took me a while to figure out how to make this work. A wiring diagram of readable size would be nice. I had to figure out that the ground wire needs to be routed to 3 positions on the driver. No diagram of this nor the wiring needed to do this. The modes are not well explained (bad translation) and poor layout so it takes some time to understand what the chart is explaining. Now it works fine for stand alone testing, but not much that be done to integrate this into an automatic system it is only for manual use.
Kayan
Comentado en Canadá el 25 de abril de 2023
Works great .
Productos recomendados