Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Irwin - Tornillo de banco para carpintero

Envío gratis en pedidos superiores a Mex $600.00

Mex $693.51

Mex $ 374 .00 Mex $374.00

En stock

1.Nombredelestilo:Tornillo De Banco


Acerca de este artículo

  • El pie para asegurar hacia la parte superior ayuda a asegurar un agarre firme en la pieza de trabajo.,
  • Asiento de cuerpo cuadrado para fácil montaje bajo el banco.,
  • Disposición para instalar mejillas de madera para proteger las piezas de trabajo.,
  • Capacidad de abertura perfecta de 6 1/2pulgadaspara tareas livianas de carpintería.



Más información del producto

1
1
1

Farooq Rahimi
Comentado en Canadá el 24 de marzo de 2024
Perfect for a DIYer. Does not come with a manual but easy to install.Here is how I did it.1. Measured pieces of wood and cut with my mitre saw.2. Made holes for the screws that would attach the vise to the table3. Opened the vise into 2 pieces4. Screwed the woods to the vise5. Screwed the vise to the table - screws are not included6. Put the vise back together
Roberto Muraoka
Comentado en México el 9 de febrero de 2024
Muy buena función para mí taller q es pequeño se cumplió con el envío en tiempo
Rafael
Comentado en México el 27 de diciembre de 2024
Es de buena calidad, y es lo que realmente buscaba
Ricardo Garcia
Comentado en México el 17 de noviembre de 2024
La rosca del tornillo es increíblemente fuerte y soporta bastante presión. Recomiendo agregarle unos páneles de madera suave para no dañar la madera que se vaya a prensar.El único detalle que no me gustó es el tamaño de la barra de ajuste; es demasiado delgada y demasiado corta; apretarla con la mano desnuda es bastante doloroso. Sólo por esto le bajo 1/2 estrella para que quede en 4 1/2 de 5.⭐⭐⭐⭐½
Nelly Susan Méndez Flores
Comentado en México el 16 de octubre de 2024
Mi papá está encantado con el producto, gran calidad
Witch Hunt
Comentado en México el 10 de septiembre de 2024
No se pudo cargar el contenido.
Miguel Angel
Comentado en México el 19 de septiembre de 2023
Producto de buena calidad, superficie pulida sin rebaba, gira con facilidad, buen cromado en sus partes, durable y a precio justo.
Salvador Aguilera
Comentado en México el 18 de septiembre de 2023
Me gusta este producto porque es muy útil y fácil de usar
Erik Márquez
Comentado en México el 1 de abril de 2023
El producto es de buena calidad aunque un poco pequeño pero de buena calidad
Shahrial Tahar
Comentado en Singapur el 14 de enero de 2022
Works smoothly. The weight and design keeps it firmly placed on the surface well.
SF
Comentado en Australia el 22 de junio de 2021
Awesome Vise that's strong, price effective and great brand. Attaching it to my workbench was a breeze and it was ready for use in under 30 mins! I highly recommend the product based on my research.
Jeuring
Comentado en Alemania el 22 de marzo de 2021
Ich kann gut damit arbeiten, habe zwei Holzteile dran geschraubt um meine Arbeitsteile zu schützen, funktioniert einwandfrei.
Christian Moussa
Comentado en los Estados Unidos el 2 de noviembre de 2020
First off, a word of warning. Do not open the clamp up all the way to the very end without holding both ends or you risk losing your toes. While testing to see how far this thing opens up, I loosened it fully, and due to the dual beam support, I was unaware that the vise had come apart as it was still slightly supported. When I tilted the vise, the front part fell about 5 inches away from my foot. It not falling on my foot was the difference between a 5-star review and a long visit to the ER. You have been warned.As for the positives, for $20, you get a woodworking vise that can handle a large variety of tasks. When you apply wooden planks to the inside of the vise, you will need to drill out 2 holes into the wood on the side that attaches to the edge of your bench. Make sure to attach your wood first, drill your holes through your wood, then predrill holes in your bench for the vice. Make sure to have your screws recessed into the wood to avoid damaging any wood you clamp.The edge where you need to screw or bolt in the vice from the underside is quite close to edge so you need to make sure to drill carefully into the side of your bench to avoid any issues. I definitely recommend measuring twice and thinking everything through before installing. The worst case would probably be chipping off a small part of the side of your bench and moving the vice to a new location. To avoid this, just be patient.I used two #10 2 1/2" screw for securing the vice horizontally and two #12 3" screws for securing it vertically. They work perfectly for the size of the holes. I pre-drilled holes with a 3/16" bit into my workbench to secure the screws. I really wanted to bolt it into the bench horizontally, but I could not find #10 5" bolt screws to secure the vice into the 4x4. It would probably be overkill anyway. I also used four #10 3/4" screws for securing the wood into the vice which worked out perfectly. The metal beams that secure the angle of the vice rubbed against one of the pieces of wood at first, but opening and closing the vice a few times wore down the part that was touching and it now works smoothly again.I used a couple of pieces of pine for the wooden clamps which work great. Pine is not hard enough to damage any wood that's clamped in the vice, but is strong enough to withstand wear. I finished them with some beeswax and this vice is good to go.The clamp holds very well and allows for some great detail work. I highly recommend this vice for the novice woodworker and the professional who just needs an extra vice for fine work on smaller pieces.
Productos recomendados

Mex $927.40

Mex $ 510 .00 Mex $510.00

4.3
Elegir

Mex $619.00

Mex $ 303 .00 Mex $303.00

4.4
Elegir