No hay artículos en el carro
No hay artículos en el carro Nombre: Tap
Cantidad: 2
Tipo de rosca: rosca derecha e izquierda
Modelo: 9/16'' - 20 TPI
Material: HSS
ES9
Comentado en los Estados Unidos el 22 de febrero de 2025
This tool worked well to repair stripped threads on a Schwinn IC4 exercise bicycle. The 25-mm crankshaft bolt on this bike is an unusual size, so it was great to be able to repair the threads without removing the crank shaft. I applied oil to the threads and tool first. I threaded the tapping tool from the inner side (the side with the good threads), and turned it by hand. When it became hard to turn, I used a wrench. I backed off the tap and repeated twice more. Then I cleaned out the small amount of metal shavings with a paper towel. I added more oil to the threads and then I was able to reinstall the pedal. [Don't be put off by the comment "this item is frequently returned'. That could be because think they can 'rent' it for free. Not good. ]
wg183
Comentado en los Estados Unidos el 5 de abril de 2025
I had messed up the RH crank peddle treads when trying to put on a new set up peddle. I used this to clean up the treads and it worked as well. One suggestion to the manufacturer. The pair of taps where marketed as RH and LH bicycle crank thread tabs. However they are not marked to identify the RH or LH tap. It would be benefical if the manufacturer put markings on the taps to indicate the LH or RH tap.
Michael U. Frank
Comentado en los Estados Unidos el 20 de septiembre de 2024
This tap set is great. My wife fell out of her peloton, the pedal coming out and damaging the threads on the right hand side crank.With a little cutting oil, I was able to quickly and easily repair the right hand crank threads. I also used the left side too since everything was already out.Great experience with this product overall!
AndruMacartu
Comentado en México el 1 de mayo de 2023
Lo use en la reparación de mi bicicleta y quedo perfecta, fue para rehacer la rosca izq principalmente..Si fueran semi conicos serían perfectos
C. Griffiths
Comentado en los Estados Unidos el 25 de marzo de 2022
These worked perfect and saved me from an expensive right crank replacement on my Peloton bike. I had my right pedal snap off at the crank and when I went to replace the pedals I found that the pedal had been cross-threaded and damaged the internal threads on the crank. Faced with a possibly long wait and expensive visit from a Peloton service tech I thought I would try this first. I was unable to start the tap on the outside of the crank due to the threads being so damaged so I did what one reviewer suggested which was to thread the repair tap in from the back side of the crank where the threads are still good. Worked like a charm. I threaded the tap all the way through until it came out the other side, used some compressed air to clean out the metal shavings and the pedal threaded in easily and in perfect alignment. What a great tool. Just make sure you use the correct tap as there is one for the right side and one for the left side and the markings are not clear. Just start slowly from the back side and there should be little to no resistance until you get to the damaged threads.
mike s.
Comentado en los Estados Unidos el 7 de mayo de 2021
Purchased a used Synapse 4 Carbon for a super deal but the crank arms seemed to have been cross threaded and would not allow me to attach my pedals from the front side. I noticed that I could partially thread them in smoothly from the rear and started to wonder if I could ream the threads and found this product was just what I was looking for. It worked beautifully allow me to carefully insert these from the back side of the crank thread after lubricating the threads and screw with a little bit of lubricant and slowly turn them thru the good portion of threads until they reached the buggered part. I then proceeded to turn 1/2 turn in then 1/4 turn out until I was all the way thru the front side. I carefully backed them back out then cleaned the new threads with nylon tooth brush to remove any metal filings then applied some more grease to the pedal threads and to my great joy then screwed in as smooth as butter. I am totally thrilled and satisfied to add these tools to my arsenal. You can tell the difference between the right and left threads by the small mark on one tool. you can also just visually compare them with the direction of threads of your pedal threads. Just be careful to use the right ones, go slow and you will be back in business in no time.
Productos recomendados
Mex $3,945.95
Mex $ 1,578 .00 Mex $1,578.00
Mex $486.28
Mex $ 257 .00 Mex $257.00
Mex $213.00
Mex $ 121 .00 Mex $121.00
Mex $471.14
Mex $ 240 .00 Mex $240.00
Mex $240.01
Mex $ 129 .00 Mex $129.00
Mex $206.27
Mex $ 113 .00 Mex $113.00