Sleeplessness
Comentado en México el 7 de febrero de 2023
La tablilla tiene evidencias de haber sido ensamblada a mano. La posición de los componentes no es la óptima y la soldadura de todo el conjunto deja mucho a desear. Hace el trabajo; sin embargo, es molesto que ofrezcan una calidad y entreguen otra inferior; además, la tablilla está muy cara en comparación con tarjetas similares. No se las recomiendo hasta que estas personas entreguen sus productos en las mismas condiciones que se muestran en las fotografías con las que los venden.
DaveD
Comentado en Australia el 4 de octubre de 2023
Does exactly what it says on the box. Works without drivers as it's a legitimate FTDI chip. The voltage switch adjusts VCC which is handy. If also has short circuit protection which is handy when you often phat finger things like me. Also tolerant to an imperfect connection to the target which is good too. Highly recommended. If I were to ask for one thing, it would be multiple grounds.
Ruben
Comentado en México el 5 de diciembre de 2022
Gracias a este Dongle pude convertir un router Netgear en un satélite
zincendorf c.
Comentado en México el 16 de diciembre de 2022
Requerimos un convertidor de Wiegand a usb así es el requerimiento
Robert
Comentado en Alemania el 1 de agosto de 2021
Es funktioniert sehr gut, ich benutze es selbst, um Sonoff-Geräte zu programmieren.
Binghi Trod
Comentado en Francia el 12 de julio de 2020
Drivers à télécharger pour une utilisation parfaite
Michele M.
Comentado en Italia el 18 de diciembre de 2020
Dopo avere perso parecchie ore/giorni per identificare un malfunzionamento di una apparecchiatura da me realizzata, che usava una schedina cinese low cost dichiarata FTDI232 compatibile, che si verificava senza un preciso schema temporale, ho avuto il sospetto che potesse esserne quella la causa. Sostituita con questa "originale", tutto si è messo a funzionare senza intoppi. Morale della favola: non è tutto oro quello che luccica e se dovete realizzare qualcosa di affidabile, usate prodotti di qualità come questo. Non fate come me, che per risparmiare qualche euro ne ho buttati via moltissimi di più in tempo e tribolazioni.
igoeco2001
Comentado en los Estados Unidos el 29 de marzo de 2018
Appears to be a rock-solid FTDI chip.Automatically detected by both my Windoze 10 and MacOS 10.12 systems.The supplied little jumper shown in the pictures installed between TXD&RXD is there to check loopback.If your terminal program echoes what you type through its assigned virtual serial port, it’s working properly.Obviously, remove before actual use.Perfect for use for its advertised purpose: a general-purpose firmware loader.However,If your primary use is with Arduino platforms that do not feature their own USB(eg. Arduino Pro Mini and clones, and others):it works fine, with the Arduino IDE & avrdude, *if* you keep in mind:1. You’ll have to rearrange the order of the pins into the Arduino, as this unit does not follow the “standard” Arduino FTDI pinout ordering.2. You’ll have to run a extra (preferably green) wire between the unit’s pad labeled “DTR#” and the Arduino’s DTR pin.I soldered a long right-angle pin to the unit’s DTR# pad and created a rearranged female-female 6-conductor cable,observing the “standard” FTDI “green/black” wire color & ordering to minimize the probability of connecting it backwards.Again, if your primary application is Arduino FTDI, there are other, smaller, cheaper, standard-wired, genuine FTDI adapters out there.Nevertheless, I kinda like this one.It’s one of the few FTDI-based adapters to feature a USB Type A” connector, useful if you want to to plug it into your laptop without a USB cable.One nitpick: I would have liked to see a schematic somewhere online, but have not found one, yet.Still, does what it claims, so 5 stars!----