No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Detalles del producto
- Modelo: NF9600 - 0110
- Tensión de entrada: 220V + - 15% 50 / 60 Hz en una sola fase / tres fases
- Tensión de salida: AC 3ph 0 - 220V 0 - 650hz
- Potencia de salida: 11 kW / 15 hp / 15CV
- Corriente nominal: 42a (el 150% de la corriente nominal es de 60 s)
- Modo de control: control vectorial de anillo abierto (svc) control V / F
- Tamaño exterior (mm): 345 * 230 * 200
- Tamaño del embalaje (mm): 385 * 300 * 290
- Peso: 8kg
Método de cableado y conexión de accesorios externos
Precauciones importantes
Esta unidad solo es adecuada para motores asíncronos de tres fases. Antes de comprar, asegúrese de que su motor es un motor asincrónico de tres fases. Para proteger el vfd, asegúrese de presionar el botón rojo "stop" al dejar de usarlo y apagar la energía.
• Our products adopt the third generation vector technology and have excellent performance.
A. 0.5Hz can provide 150% starting torque.
B. Torque response speed less than 20 ms.
C. Providing Torque Limitation to Protect Equipment Safety.
• Our products have powerful functions.
A.Current limiting function：Avoiding Frequent Over-current Alarm of Frequency Converter.
B.Power dip ride through：Instantaneous power outage time converter will not shut down.
C.Simple PLC Programming：It can achieve up to 16-segment speed operation.
D.Multiple Protection of Motor：Short-circuit, phase-absence, over-current, over-voltage, under-voltage, over-heat, over-load protection, etc.
• Our products have a comprehensive configuration.
A.Built-in brake unit：Brake function can be realized by matching brake resistance
B.18 functional terminals：Hundreds of functions can be realized through different combinations
C.Standard RS485 communication：It can communicate and monitor remotely with PLC or PC.
D.Relay output：More complex linkage control functions can be realized.
Common basic parameter settings
- Restore factory settings: PP-01=001 P0-03=2
- Acceleration and deceleration time: P0-17 plus p0-18 minus (9600)
- Adjust frequency:
- E.g. SET 60Hz: P0-10=60 P0-12=60 P0-08=60 P1-04=60
- Set lower frequency limit: P0-14=desired frequency to be set
- Rated speed adjustment speed: p1-05=desired speed to be set
- Unlock password: 11229
- Reverse: Set: 1. P7-01=2 then run 2. Function key (MF. K): switch between forward and reverse (Fix a direction to swap any two phases of UVW)
- Connect and configure the converter for the external switch of the compressor air on/off: Terminal operation can be set, with p0-02=1, X5 and DCOM connected to passive signals. If the switch is energized, convert the electrical signal of the pressure switch into a passive signal through the intermediate relay and connect it to the frequency converter. X5 and DCOM will close and start, and open and stop.
- Automatic operation: 1. P0-02=1 2. Connect X5 and DCOM
- Increase display speed: P7-03=401F
Para varios dispositivos.
Este inversor solo se puede utilizar para conectar motores asíncronos de tres fases. Su función principal es ajustar la frecuencia del motor, que puede funcionar automáticamente a varias velocidades cuando está electrificado, y es una buena ayuda para su trabajo.
Mex $1,868.99
Mex $ 915 .00 Mex $915.00