No hay artículos en el carro
No hay artículos en el carroLos controladores Zone ofrecen utilidad extendida a las familias Rack y ZonePRO de la unidad. Los controladores de nueve zonas utilizan voltaje DC analógico para proporcionar un control lógico que va desde la selección de la fuente de zona, el volumen y el silencio, hasta la selección de programas o escenas y el silencio de seguridad contra incendios. Con cable Cat5 fácilmente disponible y asequible con conectores RJ-45 universalmente aceptados a distancias de hasta 1000 pies, los controladores de zona Zc ofrecen soluciones simples pero elegantes al contratista. El ZC-FIRE es una interfaz de seguridad contra incendios dedicada para los productos ZonePRO que permite la selección de silenciamiento del sistema o selección de escenas al ser activado por un relé o voltaje de control del sistema de seguridad contra incendios. Un zc-4 también se puede utilizar como interfaz a un sistema de alarma. La guía de integración de la alarma de incendios zc-4 se puede encontrar en la sección de manuales/documentación de la página del producto zc-4.
Warren Dieno
Comentado en Canadá el 11 de julio de 2021
I use these all time for installs and they work great ! Unit came quickly and price was right !
Chris NJ
Comentado en los Estados Unidos el 12 de octubre de 2019
Great deal thanks
Marti
Comentado en los Estados Unidos el 8 de agosto de 2016
We have over 24 of the ZC-8 installed. All of them have had led failures. Working to get DBX to help support problem. Will try to update review in the future.
sharon k
Comentado en los Estados Unidos el 25 de septiembre de 2015
Perfect product easy install. I had one installed out doors and it still works after about 15 years.
E.T.
Comentado en los Estados Unidos el 12 de noviembre de 2013
First off, if you are looking at these, you know this is an accessory for another item, the DBX Driverack. These are used for remote control of an audio signal for large public/commercial installations.This allows the user to control the volume at the end location without using a fader. The signal input is reduced (or muted) before it enters the amplifier. The device mounts on the wall in the desired location.I purchased several of these for our church, and it has worked out very well for us.Installation: Once you select the location, you install an electical box in-wall (low voltage is fine) and run a Cat5 network wire to the box. Install an RJ-45 plug at both ends, set the DIP switches to control the correct channel (1-6 on our driverack) and plug the cable in to the driverack and the wall control.If you mount more than one of these, you need to plan your wiring in-line, as the network cabling connects via a daisy chain (you don't have to run from each panel to the driverack). Plan your wiring from the farthest point to the next unit in, next unit in, and so on until you get back to the drive rack. You could run normal prebuilt RJ-45 cables, but it's much better to run the Cat5 wiring first and crimp your own cables as you are installing the boxes and control panels.Once the controls are mounted and the dip switches set for the correct channels, set each wall knob at "10" and your maximum desired volume on the amplifier you will be using for that remote location. Once this is set, you never touch the amp again, and your users can turn the volume up or down as desired, and can simply mute by pressing the button (which then lights up).Since this is a control signal for the preamp in the driverack, there is no noise introduced by the wiring or the panel, so these can be run anywhere in your building. Takes a little planning but the result is worth it. These units allowed dedicated control in each location without having to run up and down the stairs to pass along requests for more or less volume.Everyone who uses our system is very pleased with the control they have. Highly recommended!
Productos recomendados
Mex $3,300.00
Mex $ 1,650 .00 Mex $1,650.00
Mex $2,080.90
Mex $ 936 .00 Mex $936.00
Mex $5,266.80
Mex $ 1,881 .00 Mex $1,881.00