No hay artículos en el carro
No hay artículos en el carro Especificaciones:
Fuente de alimentación: DC6V-15.5V
Potencia: celda AA de 1,5 V (batería incluida)
Rango de conteo: 0----99999
Restablecer el ancho mínimo de pulso: 0,1 s.
Método de reinicio: panel manual/ externo
Cuenta la frecuencia más alta: 20 Hz o 20 veces/s
Temperatura de trabajo: 5 a 40 °C.
Cuenta el ancho de pulso mínimo: 10 ms
Sensor de interruptor de promezclidad: 2 cables, longitud: 110 mm, viene con imán
Distancia de detección: 3-10 mm.
Tamaño: 63 x 38 x 30 mm.
Tamaño del agujero: 61 x 36 mm.
Resistencia máxima cuando el punto de conexión en: ≤ 10 KΩ
Resistencia mínima cuando el punto de conexión: ≥ 500 KΩ
Peso neto: 0,05 kg
Manmohan
Comentado en India el 5 de marzo de 2025
Good
Peter Brooke
Comentado en Canadá el 25 de marzo de 2024
Put this on a test rig and it was easy to install and worked reliably
Anita
Comentado en México el 20 de noviembre de 2022
Muy rapido de instalar. Considerar adquirir baterias
jenny payne
Comentado en el Reino Unido el 31 de octubre de 2022
brought to fit on a sentro knitting machine as counter had started to not tick over on row count ,easy to fit and set up . I used Velcro to attach so could use between two different machines, works and keeps count perfectly.
Elec/CS engineer
Comentado en los Estados Unidos el 5 de mayo de 2019
First, this device works as advertised. There are connection instuctions in English (simple). Battery replacement is easy although lasts a very long time. The sensor is more sensitive than they say, maybe 1/2 - 3/4 inch and that is with their little button magnet. The stronger the magnet the greater the distance. A great deal since the hall sensor or the counter is worth the price alone. The provided sensor doesn't have to be used. Any switch, of any sort, will work. It is also very nice that they include that small bracket that holds the sensor and the sensor has a long threaded neck, with two nuts, that allow adjust the distance from the magnet after installation. They don't mention but to reset the counter, you can used an attached switch or just press the pause button a couple of times. See the attached picture for my application where I count the revolutions of the rear tire of my lawn tractor (I just snapped the button magnet on the tire rim (two magnets would give two counts per revolution). It bounces around quite a bit but that doesn't phase the sensor. They provide a bracket for mounting the counter or you can use a another magnet. Just remember that this is not a high speed counter, maybe 10-20 counts per second or 600-1200 rpm and depends to some extent on the strength of magnet and sensing distance. In addition, it only counts up since the sensor can't tell whether the magnet is coming or going.
Cliente
Comentado en España el 14 de mayo de 2019
cumple con lo esperado y es de facil implementacion
Productos recomendados
Mex $292.00
Mex $ 131 .00 Mex $131.00
Mex $275.00
Mex $ 151 .00 Mex $151.00
Mex $2,791.86
Mex $ 1,395 .00 Mex $1,395.00
Mex $296.00
Mex $ 136 .00 Mex $136.00
Mex $166.00
Mex $ 99 .00 Mex $99.00