No hay artículos en el carro
No hay artículos en el carroDescripción del producto
JIUWU - Fresadora de extremo de carburo de 1,5 mm, fresadora CNC, fresadora de extremo para máquina PCB, paquete de 10
Material: carburo sólido (acero Tungsten). Diámetro del vástago: 3,175 mm. Diámetro del filo: 1,5 mm. Longitud del borde de corte: 9 mm. Longitud total: aprox. 37,00 ± 0,20 mm
Estas brocas de grabado tienen suficiente resistencia a la flexión y resistencia al desgaste. Fresado, agujero y borde de placa, superficie limpia, ordenada, sin rebabas. Hecho de material de carburo de grano ultrafino que tiene buenas propiedades de fresado para garantizar un trabajo eficiente. Una amplia gama de materiales se puede grabar, incluyendo: Tableros de circuito, metal, mayoría de plásticos, madera, SMT, fibra de vidrio, carbono, FR-4, placa CEM-3 y tablero ambiental. El paquete incluye: 10 puntas de grabado de metal de carburo de 1,5 mm
Reviews by Dan
Comentado en los Estados Unidos el 8 de febrero de 2025
Fit key perfectly providing good protection. Seems durable. Feels like silicone/rubber, so it’s non slip but does collect some lint. Easy to install and a good value.
Robert Parker
Comentado en los Estados Unidos el 21 de diciembre de 2024
These are what they are, disposable end mills. I use these in my Snapmaker and they seem to be holding up just fine.
Robert Parker
Comentado en los Estados Unidos el 21 de diciembre de 2024
These are what they are, disposable end mills. I use these in my Snapmaker and they seem to be holding up just fine.
Robert Parker
Comentado en los Estados Unidos el 21 de diciembre de 2024
These are what they are, disposable end mills. I use these in my Snapmaker and they seem to be holding up just fine.
Robert Parker
Comentado en los Estados Unidos el 21 de diciembre de 2024
These are what they are, disposable end mills. I use these in my Snapmaker and they seem to be holding up just fine.
Robert Parker
Comentado en los Estados Unidos el 21 de diciembre de 2024
These are what they are, disposable end mills. I use these in my Snapmaker and they seem to be holding up just fine.
Robert Parker
Comentado en los Estados Unidos el 21 de diciembre de 2024
These are what they are, disposable end mills. I use these in my Snapmaker and they seem to be holding up just fine.
Robert Parker
Comentado en los Estados Unidos el 21 de diciembre de 2024
These are what they are, disposable end mills. I use these in my Snapmaker and they seem to be holding up just fine.
Robert Parker
Comentado en los Estados Unidos el 21 de diciembre de 2024
These are what they are, disposable end mills. I use these in my Snapmaker and they seem to be holding up just fine.
Brian
Comentado en los Estados Unidos el 21 de noviembre de 2024
Protects your fobs and easy to remove when it's time to change the battery. Looks really nice too.
Jay
Comentado en los Estados Unidos el 26 de octubre de 2024
Perfect fit.
Harvey Tucker
Comentado en los Estados Unidos el 11 de mayo de 2020
I use these on my Shapeoko to cut very fine lines and thin woods. They work really well for that as long as you dont push them too hard. Also, you have to crank your 1/8" collet down a little tighter than normal to hold these, so they are a pain to get the collet to release when done cutting. I usually have to tape the collet nut with a screwdriver for a bit to get it to release, and half the time i end up missing the nut and snapping the bit off. They are fragile, but do what you need.
Harvey Tucker
Comentado en los Estados Unidos el 11 de mayo de 2020
I use these on my Shapeoko to cut very fine lines and thin woods. They work really well for that as long as you dont push them too hard. Also, you have to crank your 1/8" collet down a little tighter than normal to hold these, so they are a pain to get the collet to release when done cutting. I usually have to tape the collet nut with a screwdriver for a bit to get it to release, and half the time i end up missing the nut and snapping the bit off. They are fragile, but do what you need.
Harvey Tucker
Comentado en los Estados Unidos el 11 de mayo de 2020
I use these on my Shapeoko to cut very fine lines and thin woods. They work really well for that as long as you dont push them too hard. Also, you have to crank your 1/8" collet down a little tighter than normal to hold these, so they are a pain to get the collet to release when done cutting. I usually have to tape the collet nut with a screwdriver for a bit to get it to release, and half the time i end up missing the nut and snapping the bit off. They are fragile, but do what you need.
Harvey Tucker
Comentado en los Estados Unidos el 11 de mayo de 2020
I use these on my Shapeoko to cut very fine lines and thin woods. They work really well for that as long as you dont push them too hard. Also, you have to crank your 1/8" collet down a little tighter than normal to hold these, so they are a pain to get the collet to release when done cutting. I usually have to tape the collet nut with a screwdriver for a bit to get it to release, and half the time i end up missing the nut and snapping the bit off. They are fragile, but do what you need.
Harvey Tucker
Comentado en los Estados Unidos el 11 de mayo de 2020
I use these on my Shapeoko to cut very fine lines and thin woods. They work really well for that as long as you dont push them too hard. Also, you have to crank your 1/8" collet down a little tighter than normal to hold these, so they are a pain to get the collet to release when done cutting. I usually have to tape the collet nut with a screwdriver for a bit to get it to release, and half the time i end up missing the nut and snapping the bit off. They are fragile, but do what you need.
Harvey Tucker
Comentado en los Estados Unidos el 11 de mayo de 2020
I use these on my Shapeoko to cut very fine lines and thin woods. They work really well for that as long as you dont push them too hard. Also, you have to crank your 1/8" collet down a little tighter than normal to hold these, so they are a pain to get the collet to release when done cutting. I usually have to tape the collet nut with a screwdriver for a bit to get it to release, and half the time i end up missing the nut and snapping the bit off. They are fragile, but do what you need.
Harvey Tucker
Comentado en los Estados Unidos el 11 de mayo de 2020
I use these on my Shapeoko to cut very fine lines and thin woods. They work really well for that as long as you dont push them too hard. Also, you have to crank your 1/8" collet down a little tighter than normal to hold these, so they are a pain to get the collet to release when done cutting. I usually have to tape the collet nut with a screwdriver for a bit to get it to release, and half the time i end up missing the nut and snapping the bit off. They are fragile, but do what you need.
Harvey Tucker
Comentado en los Estados Unidos el 11 de mayo de 2020
I use these on my Shapeoko to cut very fine lines and thin woods. They work really well for that as long as you dont push them too hard. Also, you have to crank your 1/8" collet down a little tighter than normal to hold these, so they are a pain to get the collet to release when done cutting. I usually have to tape the collet nut with a screwdriver for a bit to get it to release, and half the time i end up missing the nut and snapping the bit off. They are fragile, but do what you need.
Matt
Comentado en los Estados Unidos el 16 de junio de 2019
I'm new to CNC routing, but the first bit I used cut great, and I have 9 others to back that one up. Good cutter and good price. I looked at the tips under a scope and the grinding looked very good for such a tiny cutter.
Matt
Comentado en los Estados Unidos el 16 de junio de 2019
I'm new to CNC routing, but the first bit I used cut great, and I have 9 others to back that one up. Good cutter and good price. I looked at the tips under a scope and the grinding looked very good for such a tiny cutter.
Matt
Comentado en los Estados Unidos el 16 de junio de 2019
I'm new to CNC routing, but the first bit I used cut great, and I have 9 others to back that one up. Good cutter and good price. I looked at the tips under a scope and the grinding looked very good for such a tiny cutter.
Matt
Comentado en los Estados Unidos el 16 de junio de 2019
I'm new to CNC routing, but the first bit I used cut great, and I have 9 others to back that one up. Good cutter and good price. I looked at the tips under a scope and the grinding looked very good for such a tiny cutter.
Matt
Comentado en los Estados Unidos el 16 de junio de 2019
I'm new to CNC routing, but the first bit I used cut great, and I have 9 others to back that one up. Good cutter and good price. I looked at the tips under a scope and the grinding looked very good for such a tiny cutter.
Matt
Comentado en los Estados Unidos el 16 de junio de 2019
I'm new to CNC routing, but the first bit I used cut great, and I have 9 others to back that one up. Good cutter and good price. I looked at the tips under a scope and the grinding looked very good for such a tiny cutter.
Matt
Comentado en los Estados Unidos el 16 de junio de 2019
I'm new to CNC routing, but the first bit I used cut great, and I have 9 others to back that one up. Good cutter and good price. I looked at the tips under a scope and the grinding looked very good for such a tiny cutter.
Matt
Comentado en los Estados Unidos el 16 de junio de 2019
I'm new to CNC routing, but the first bit I used cut great, and I have 9 others to back that one up. Good cutter and good price. I looked at the tips under a scope and the grinding looked very good for such a tiny cutter.
Dianna Maxwell
Comentado en los Estados Unidos el 31 de agosto de 2018
Works well, would be better if their sizes were labeled on each bit.
Dianna Maxwell
Comentado en los Estados Unidos el 31 de agosto de 2018
Works well, would be better if their sizes were labeled on each bit.
Dianna Maxwell
Comentado en los Estados Unidos el 31 de agosto de 2018
Works well, would be better if their sizes were labeled on each bit.
Dianna Maxwell
Comentado en los Estados Unidos el 31 de agosto de 2018
Works well, would be better if their sizes were labeled on each bit.
Dianna Maxwell
Comentado en los Estados Unidos el 31 de agosto de 2018
Works well, would be better if their sizes were labeled on each bit.
Dianna Maxwell
Comentado en los Estados Unidos el 31 de agosto de 2018
Works well, would be better if their sizes were labeled on each bit.
Dianna Maxwell
Comentado en los Estados Unidos el 31 de agosto de 2018
Works well, would be better if their sizes were labeled on each bit.
Dianna Maxwell
Comentado en los Estados Unidos el 31 de agosto de 2018
Works well, would be better if their sizes were labeled on each bit.
P. Withers
Comentado en el Reino Unido el 4 de noviembre de 2016
Good quality
P. Withers
Comentado en el Reino Unido el 4 de noviembre de 2016
Good quality
P. Withers
Comentado en el Reino Unido el 4 de noviembre de 2016
Good quality
P. Withers
Comentado en el Reino Unido el 4 de noviembre de 2016
Good quality
P. Withers
Comentado en el Reino Unido el 4 de noviembre de 2016
Good quality
P. Withers
Comentado en el Reino Unido el 4 de noviembre de 2016
Good quality
P. Withers
Comentado en el Reino Unido el 4 de noviembre de 2016
Good quality
P. Withers
Comentado en el Reino Unido el 4 de noviembre de 2016
Good quality
Productos recomendados
Mex $217.99
Mex $ 115 .00 Mex $115.00
Mex $399.83
Mex $ 199 .00 Mex $199.00
Mex $350.00
Mex $ 178 .00 Mex $178.00
Mex $819.86
Mex $ 401 .00 Mex $401.00
Mex $404.47
Mex $ 210 .00 Mex $210.00
Mex $6,261.43
Mex $ 1,881 .00 Mex $1,881.00