No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Sustituye a P/N: 89742-AA040
Para FCC ID: GQ43VT20T
Para IC/otros: 1470A-1T
Programación: Autoprogramable con una tecla de trabajo
BOB C
Comentado en los Estados Unidos el 29 de enero de 2025
I use the QR code to locate the instructions for programming my Avalon. It took me a couple three tries to properly execute the very clear instructions. That’s on me.Once programmed, this remote works perfectly! I’m going to order one for myself, as they’re reasonably priced). For my next car, I’ll be bold and order a set of two - and program them at the same time!Happy wife, happy life!Thank you, REMOTESTEMOTES.com
Igor T.
Comentado en los Estados Unidos el 21 de abril de 2025
Perfectly fits Toyota Avalon 2005!
Timothy Goode
Comentado en los Estados Unidos el 8 de abril de 2025
👍🏾All I have to add... PERFECT AND SUPER EASY TO PROGRAM 👍🏾
joyce markley
Comentado en los Estados Unidos el 24 de abril de 2025
Only worked for 2 days.
Mark Hedge
Comentado en los Estados Unidos el 3 de septiembre de 2023
Product took two minutes to program. I had my doubts, but it was truly as easy as following these instructions that I got from another purchaser.1. Start withThe key out of the ignition,Drivers door is open,All other doors and trunk should be closed and driver’s door is unlocked.All other doors are locked2. Perform these steps within 5 seconds.A. Insert the key into the ignition (Do NOT Turn it) and Pull key out.B. Insert the key into the ignition (Do NOT Turn it) and Pull key out.3. Perform these steps within 40 seconds.A. Close then open the driver’s door.B. Close then open the driver’s door.C. Insert the key into the ignition (Do NOT Turn it) and Pull key out.4. Perform these steps within 40 seconds.A. Close then open the driver’s door.B. Close then open the driver’s door.C. Insert the key into ignition and leave it in the ignition.D. Close the driver’s door.E. Turn the ignition to ON (Do NOT Start or crank engine) then back to OFF.F. Remove the key from the ignition.5. Within 3 seconds,The power door locks should lock then unlock automatically indicating successful entry into programming mode.Return to step 1 if the door locks do not cycle at this point.At this point the programming mode has been entered. I think that it stays in programming until the door is opened.6. Perform these steps within 40 seconds.A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.B. Immediately after letting go of the lock and unlock buttons,Press the lock button by itself and hold for 2 seconds.Within 3 seconds, the door locks should lock and then unlock once indicating successful programming.If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.C. Repeat steps A and B in step 6 for each new remote.7. Open driver’s door.8. Test the newly programmed remotesIf the regular process does not work, TRY PROCESS WITH ALL CAR DOORS UNLOCKED
Alejandro Ramos Pavian
Comentado en México el 2 de abril de 2020
Excelente 100% funcional. Gracias.
Productos recomendados
Mex $339.75
Mex $ 183 .00 Mex $183.00
Mex $161.11
Mex $ 80 .00 Mex $80.00
Mex $408.12
Mex $ 216 .00 Mex $216.00
Mex $251.00
Mex $ 148 .00 Mex $148.00
Llavero compatible con Viper Hornet DEI Hyundai Rattler de repuesto con alarma sin llave (EZSDEI471)
Mex $504.35
Mex $ 277 .00 Mex $277.00
Mex $306.00
Mex $ 137 .00 Mex $137.00