No hay artículos en el carro
No hay artículos en el carrokwmobile - Made for Smart Electronics
- ¡Deja volar tu imaginación! Utiliza este módulo para cualquier proyecto, ya sea para instalar alarmas, luces o diferentes sistemas.
- Para ampliar el rango de alcance, tienes soldar un alambre de cobre al XY-FST en el punto de contacto ANT.
- Encuentra más dispositivos compatibles con Arduino y Raspberry Pi entre nuestros artículos. ¡Echa un vistazo!
- Emisor: MX-FS-03V / Receptor: MX-05V
- Voltaje del emisor: 3.5 - 12 V DC / receptor: 5 V DC
- Alcance: 20 - 200 M (depende del voltaje)
- Modo de operación: AM/ sensibilidad: -105 DB
- Potencia de transmisión: 10 MW / frecuencia de emisión y recepción: 433 MHZ
- Velocidad de transmisión: 4 KB / S / corriente de reposo: 4 MA
- Dimensiones del emisor: 19 x 19 MM / receptor: 30 x 14 MM / pinout: data, VCC, peso (de izquierda a derecha)
- 3x módulos receptores transmisores de radio inalámbricos kwmobile
- Compatible con dispositivos Raspberry Pi y Arduino.
Nomic
Comentado en el Reino Unido el 4 de julio de 2023
kwmobile goods tend to be good quality and these work fine.Sending data via RF (radio frequency) tends to be noisy and hit & miss and frowned on by the techo snobs whose alternatives like 2.4ghz also has range problems.These are ideal for beginners and there are loads of tutorials out there and you will need to 'include' the Radio Head library -all for free.DO NOTE if you are setting up they need to be very close ( I mean inches) to each other. Once you are happy they talk to each other a must is to attach and aerial. This is simply a 17cm ( near 6 inch) wire to both the transmitter and receiver. No need for a thick wire and insulation on the wire makes no difference. The Transmitter has a hole in the bottom corner easy to solder to and the Receiver has a soldered joint in the corner edge near the coil - a bit trickier to solder. Once done you are laughing.I put the wires inside a straw to stop them flopping down.Using mine to monitor a rain sensor in the garden (you need an Arduino at both ends by the way as there are no 'remote sensors') and for distance of about 25 feet and thru' two solid walls it works. Watch too that you external sensor if running off a power bank can got to sleep and needs rebooting and I've yet solve that.
Andreas
Comentado en Suecia el 7 de agosto de 2021
I tried all 3 receivers with the same wiring setup and got a different result each time- First receiver got alot of noise (i live in the country side so there shouldn't be that much). Im guessing it was picking up from the wrong wavelengths or something. The things i was trying to pickup did not show.- Second receiver got no data all- Third receiver got barely any data, and the data it did get did not correspond to what i was trying to sendThe transmitters seem to work ok though, so i guess thats 50% of the product atleast..
Corsa
Comentado en España el 29 de diciembre de 2021
Buen producto y funciona sin ningún problema
James1945
Comentado en Francia el 15 de enero de 2021
Aucun soucis fonctionnent très bien. Certes, la portée est relativement limitée mais l'encombrement est discret.Livrés le lendemain de la commande et bien emballés..
Sven
after soldering on a antenna wire of about 20cm's , very clear signal, very little noise. would recommend.
Productos recomendados
Mex $4,505.28
Mex $ 1,847 .00 Mex $1,847.00
Mex $149.00
Mex $ 80 .00 Mex $80.00