No hay artículos en el carro
No hay artículos en el carroLee Precision 223 El juego de 3 matrices Pacesetter incluye una matriz de tamaño completo, una matriz de asientos de bala, una matriz de crimpado de fábrica, un soporte universal de cáscara, un cucharón de polvo e instrucciones con datos de carga.
Maclurites
Comentado en los Estados Unidos el 13 de marzo de 2025
I got this die set to replace a single die that I had broken. The Lee set is great quality for the price.
Josh
Comentado en Canadá el 5 de febrero de 2024
If you've never used dies with a shouldered case before make sure to clean the inside of all dies with cleaning solvent and give them a through cleaning. After add a very small drop of lube and take your time using these dies as they are very tight for the first few rounds. I am very satisfied with these.
Pietro Romano
Comentado en Italia el 13 de mayo de 2023
Ottimi in qualità e prezzo nella media
Pierpaolo
Comentado en Italia el 10 de abril de 2022
Non ho avuto modo di comparare il prodotto con altri di altre marche. Personalmente sono soddisfatto anche se poi, sparando con Bolt action ho acquistato a parte dies per ricalibratura del solo colletto non essendo inserito nella confezione.
Javier Mena
Comentado en México el 25 de enero de 2020
El producto está muy bien constituido buen material
Galindo.electron
Comentado en México el 4 de diciembre de 2019
Económico y de buena calidad
Rib-I
Comentado en los Estados Unidos el 11 de julio de 2014
I exclusively use Lee dies because I have had good luck with them and they are priced right. This is a great set because it restores brass cases to factory form so cases fired from any gun can be reloaded and will work perfect (opposed to the other less set that only resets the neck).I've been loading hornady cannelured 22 (.224) 55gr bullets and have extremely good luck. I find that when I trim my brass to recommended length (1.760") and I seat the bullet right at the cannelure that the OAL ends up being about 2.220" which performs excellent in my Colt Le6920.For set up, follow the instructions and you should have no problems. Since the factory crimp die is separate I started out by using the bullet seating die and progressively tightening it until the cannelure sate just right in the case. You can continue to tighten it to further seat the bullet to your liking before switching to the factory crimp die (bullets with cannelure is not required but I recommend it since it provides easy guidance for bullet depth). I use a light crimp and have been having good luck.Now for a couple of pointers. I bought the lee universal decapping die to remove all primers to protect my sizing die. I've had several pins break and figure its better to break the universal die pin than the sizing die pin. So basically I have these three dies and the universal decapping die in the turret press at all times and just crank away. However, lately I switched out the decapping die and dropped the universal powder through die in the rotation and like it better so I can leverage four pulls and yield a functional round. If you have a five hole turret then this is a non-issue. I still weigh each load individually (not sure I trust a powder thrower at this point) but the powder through die speeds things up significantly.Lastly, these are standard dies so they will fit in any press. Use lube... I spray Hornady One Shot (can is about $10) on approximately 50-75 rounds in a small shoe box and then shake them around in there to get lube all over.
Productos recomendados
Mex $223.57
Mex $ 118 .00 Mex $118.00
Mex $1,919.90
Mex $ 863 .00 Mex $863.00
Mex $723.10
Mex $ 347 .00 Mex $347.00
Mex $4,066.50
Mex $ 1,881 .00 Mex $1,881.00