Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Paquete de 2 cartuchos NTC 100K B3950 Termistor OD3mm Sensor de alta temperatura 280℃ para impresora 3D Ender 3 V2 Pro CR10 V6 PT100 Calentador Block 3D

Envío gratis en pedidos superiores a Mex $600.00

Mex $285.60

Mex $ 148 .00 Mex $148.00

En stock
  • Un termistor hecho a medida encapsulado en un paquete de cartuchos fácil de usar. Este sensor es capaz de medir temperaturas más altas de hasta 280 °C.
  • Los jugadores de bricolaje también pueden modificar BLOCK por sí mismos. Haz un agujero OD3mm en BLCOK, entonces puedes utilizar este termistor, o fuente el bloque calefactor de la versión PT100 que tiene un agujero de identificación de 3 mm. Si necesitas bloque calefactor de versión V6 PT100, comprueba este ASIN "B08NPKF2GC"; si necesitas bloque térmico Ender o CR10 versión PT100, busca este ASIN " "
  • Longitud del cable de 1 metro, alta precisión: 1%; valor de resistencia a 25 °C = 100 K; B3950, aislamiento de cableado de material personalizado de alta temperatura. Con funda de material de latón, hace que la detección de temperatura sea más sensible
  • Ajuste de Firmware Marlin: *13:100k Hisens 3950 1% hasta 300°C para hotend "Simple One" &"Hotend "All In ONE" #define TEMP_SENSOR_0 13 https://github.com/MarlinFirmware/Marlin/blob/1.1.x/Marlin/thermistortable_13.h h
  • Paquete: 2 cartuchos de 3 mm 3950B termistor


Configuración de firmware Marlin: *13:100k Hisens 3950 1% hasta 300°C para hotend "Simple One" &"Hotend "All In One" #define TEMP_SENSOR_0 13 https://github.com/MarlinFirmware/Marlin/blob/1.1.x/Marlin/thermistortable_13 h


ANTONIOS KATSANIS
Comentado en Alemania el 14 de marzo de 2025
It operated normally,item was as described
Dean Hedin
Comentado en los Estados Unidos el 6 de julio de 2024
I used this to upgrade my printer to operate up to 325C. You need customize the firmware to do this.
mark liesicke
Comentado en el Reino Unido el 30 de diciembre de 2024
I Recently upgraded to a BMS Dragonfly by Phaetus and required a cartridge thermistor, as i found the adaptor they provided rather cheap and flimsy. I read in another review that the cable was too short, so i created an extension cable from a JST-XH connector pair, however it does natively fit an original ender 3. The thermistor is accurate up to around 300 degrees, which i tested with a heatgun. I Wouldn't trust it past 320 personally, as it runs under actual temp, rather than over.Overall this exceeds specification (in my specific unit) and is great for upgrading your hotend
Michele
Comentado en Italia el 4 de junio de 2023
Sensori di qualità, consigliati. Li uso con una Makerbase THR42
Malcolm Clark
Comentado en el Reino Unido el 16 de diciembre de 2023
Perfect fit for the creality spider all metal hotend, 3mm diameter and about 15mm long. Sadly the cable is not long enough to get back to the board for the Ender 3V2. Managed to extend the cable using the replaced wire, some solder and heat shrink but just FYI
Productos recomendados