No hay artículos en el carro
No hay artículos en el carroCaracterísticas: ATMEGA32U4 funciona a 1.5V/16MH Compatible con Arduino IDE V1.0.1. Interfaz micro USB para programación 4 pines ADC de 10 bits. 12 E/S digitales (capacidad de 5 PWM) Conexiones seriales de hardware Rx y Tx 1. El Pro Micro es similar al Pro mini, pero con un ATmega32U4 integrado. El transceptor USB dentro del 32U4 nos permite añadir conectividad USB a la placa y quitar la voluminosa interfaz USB externa. 2. Esta pequeña placa hace todos los trucos de Arduino con los que estás familiarizado: 4 canales ADC de 10 bits, 5 pines PWM, 12 DIO y conexiones seriales de hardware Rx y Tx. Corriendo a 16 MHz y 5 V, esta placa te recordará tus otras placas favoritas compatibles con Arduino, pero este pequeño puede ir casi a cualquier lugar. 3. Si está proporcionando una fuente de alimentación no regulada a la placa, asegúrese de conectarse al pin "RAW" en lugar de "VCC". 1. Cuando abras el software Arduino IDE, ve a Herramientas y selecciona el tablero "Arduino Leonardo" 2. El rango de voltaje aceptable es de 5 a 9 V.
Customer
Comentado en los Estados Unidos el 4 de marzo de 2025
I bought this product because I needed a crystal oscillator based Arduino. I had trouble getting the first program loaded onto it. It shows up in the IDE as a Leonardo, and if you accidentally upload with that setting, the USB interface code in the Pro Micro is erased.It's tricky to restore the bootloader, here's a method that works:The process of resetting of the Arduino Pro Micro is a bit tricky as it doesn’t have a hardware RESET button.Nevertheless it still can be put in a bootloader reset mode by wiring twice the RST (reset) and GND (ground) pins – use for this a piece of a wire or create a temporary button.1. Open an empty sketch in the Arduino IDE and select the correct board and processor:Top Menu -> Tools -> Board: "SparkFun Pro Micro"Top Menu -> Tools -> Processor: "ATmega32U4 (5V, 15MHz)"2. Connect the Arduino Pro Micro to the PC using the USB cable3. Quickly short the RST to GND twice and select the serial port that should appear in the Arduino IDE(you will have only 8 seconds for this):Top Menu -> Tools -> Port: "" -> Serial ports4. Start uploading the empty sketch ( Ctrl + U ) and when the status changes from “Compilingsketch…” to “Uploading…”, quickly short the RST to GND pins twice again and wait for uploadingprocess to finish:Top Menu -> Sketch -> UploadOnce the status changes to “Done uploading.” it will mean that it worked – you have successfully reset theArduino Pro Micro board and restored the bootloader.I found this on the web, but Amazon will allow a link to the site.
T
Comentado en Canadá el 11 de marzo de 2025
Boards work fine, missing header pins in one package, no way to contact support without returning all items.
Tracey H.
Comentado en los Estados Unidos el 27 de febrero de 2025
Easy to program and works as expected. The tiny form-factor is great.
Zachary Eck
Comentado en los Estados Unidos el 16 de abril de 2025
All three worked, no issues so far with them, been working great to make game controllers.
David Anderson
Comentado en los Estados Unidos el 6 de abril de 2025
Nice board. Leonardo. Soldered pins myself. Used breadboard to hold all pins in place while soldering.Easy to use with Arduino IDE.
Steve
Comentado en los Estados Unidos el 23 de febrero de 2023
We used to have a stone water bowl for our pet snake. She would coil up in it and eventually she managed to crack it and it started leaking water. We were worried about her doing the same thing to this one. Well, she's been curled up in there moating and everything is good. She likes to just kick it in the corner bowl and it hasn't broken or cracked. It been a couple of months so I want to say we are very satisfied! Can't beat it for the size and price! She just shedded again and the skin came off perfectly! I tried to get it in the first picture, you might be able to see it under her on the right lower portion of the picture.
Marc A Hershkowitz
Comentado en los Estados Unidos el 9 de diciembre de 2023
It is huge lol I got it for my ball python baby because I know he’ll grow bigger, but he is enjoying it, it is like a pool for him haha. But as this bowl is big, it is heavy too and it is a little inconvenient to put it inside or take it outside of the tank with water on it, the water ends up spilling as I manage to put it in or take it outside the tank. Also the adhesive from the sticker wouldn’t come off🤦🏽♀️But overall good purchase.
Kathryn
Comentado en los Estados Unidos el 15 de noviembre de 2023
I purchased this for my ball python, who is 2 years old and about 3 feet long. He can almost fully submerge himself in it, which helps with shedding. He drinks from it as well. There is no weird coating or smell, and no cracks. It fits perfectly in the corner and has enough weight that it doesn’t move around. The color is exactly what is pictured, a gray ish color. Overall a great purchase!
Carrie
Comentado en los Estados Unidos el 3 de marzo de 2021
This is even bigger than I expected. Perfect for our ball python! She likes to burrow under things in her tank and this is no exception. It is super sturdy and even with her going under it, no spills. Great quality and looks good!
handyandy
Comentado en los Estados Unidos el 3 de noviembre de 2021
These are strong and easy to clean. They could be designed with a little more creativity but, they do the Job as is.
Productos recomendados
Mex $441.38
Mex $ 216 .00 Mex $216.00
Mex $5,454.90
Mex $ 1,881 .00 Mex $1,881.00
Mex $200.00
Mex $ 110 .00 Mex $110.00
Mex $295.58
Mex $ 147 .00 Mex $147.00
Mex $3,199.00
Mex $ 1,567 .00 Mex $1,567.00
Mex $154.69
Mex $ 81 .00 Mex $81.00
Mex $290.00
Mex $ 153 .00 Mex $153.00
Mex $369.99
Mex $ 173 .00 Mex $173.00