No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Linden Baker
Comentado en el Reino Unido el 1 de abril de 2025
Easy to install once you get the machine apart.. lolIf I’m honest they aren’t as thick as originals therefore the plastic pin wheels become an issue…so be mindful of the pin wheel’s position going forward they will leave marks on heavier card stock.That said the matts load as they should and lets me continue to use my machine again.Minimal cost…overall quite satisfied with outcome.How long they will last remains to be seen.Thank You
Dris10
Comentado en Australia el 14 de diciembre de 2024
Worked well. Glad it came in a 4 pack as I was a bit rough with one and ruined it when I was replacing it so was happy to have a spare. Been using them for a couple months now without any issues.
Randall Prentice
Comentado en los Estados Unidos el 25 de julio de 2023
These seem like they're going to hold up. They're a much harder material than the originals. They fit perfectly. Installing them was quite challenging though. Luckily there are multiple YT videos with people doing it but it takes patience. You've got to take a lot of the unit apart pretty much. There is a gear that you can't remove to get to the roller bar but you have to remove a C-ring on the bar behind the gear. It is a delicate thing to do without losing the ring inside of the machine and having to disassemble further.You need specific tools to do this job. Torx T2 screw driver. a TINY phillips screw driver (I have a small ratcheting screwdriver which helped - Craftsman CMHT68008 is the one I used). Some pry tools for small electronics. I have a set from iFixit which had a lot of useful stuff in it plus the bits are magnetized so pieces that I detached just stuck right to it and didn't fall into the machine. I also found that a small metal tube or hole was necessary to drive the wheels onto the bar. Doing it by hand was never gonna happen. But I found a hole that was bigger than the bar yet smaller than the wheel so I could drive the wheel on. Then it slid into place nicely. Follow their instructions heating them up in water first.Reassembly is just as delicate. Remember where all your pieces came from! Don't drop them further into the machine by accident. The housing unit needs to be situated just right. There are some channels on the backside that can be easily missed if you don't slide the housing into them.A lot of what I mentioned isn't in the videos on YT. I had to discover for myself. But as for the product itself, they feel solid and I believe they'll last. I ran a job on them immediately after I installed them and it ran the job great. No complaints.Good luck!
Jose Medrano
Comentado en Canadá el 23 de mayo de 2023
Ma Maker et comme neuve maintenant les ancien étaient très lousse et mon tapis aller tout croche . Depuis que j’ai mis ceux là c’est parfait !!!! Voir des vidéos sur YouTube comment changer
Miriam González Villegas
Comentado en México el 18 de abril de 2023
Han funcionado muy bien aunque es muy difícil de poner en el tubo de la critcut.
Bud
Comentado en Canadá el 9 de abril de 2023
If your rubber Cricut wheels are falling apart and no longer helping guide your mat through the machine these will help! You’ll need to take the machine apart with the help of some YT videos but worth it!Thanks!
Productos recomendados
Mex $6,433.39
Mex $ 1,881 .00 Mex $1,881.00
Mex $5,549.00
Mex $ 1,881 .00 Mex $1,881.00
Mex $5,320.50
Mex $ 1,881 .00 Mex $1,881.00
Mex $9,992.35
Mex $ 1,881 .00 Mex $1,881.00
Mex $308.51
Mex $ 151 .00 Mex $151.00
Mex $3,402.43
Mex $ 1,565 .00 Mex $1,565.00