No hay artículos en el carro
No hay artículos en el carroDescripción del producto
funda para Moto G24 y G04 y G04s y E14 4G case
La protección antichoque y anticaída absorbe el impacto de una caída y protege eficazmente el teléfono.
Los bordes elevados protegen la cámara y la pantalla
Ajusta perfectamente con los botones de volumen y es super comoda, acabado mate y si es anti huellas.
Fácil de limpiar y desmontable para su lavado.
Protege totalmente tu teléfono móvil.
muy ligero y da la impresión de no tener funda, así que si no quieres una de esas fundas grandes y voluminosas, este es el camino a seguir.
Compatible con la función de carga inalámbrica, coloca el teléfono en el cargador inalámbrico sin quitar la funda.
Sensación suaSensación suave y sedosa en la mano, fácil de sostener, suave y cómoda al tocar la funda esmerilada del teléfono, satisface sus necesidades diariasve y sedosa en la mano, fácil de sostener, suave y cómoda al tocar la funda esmerilada del teléfono, satisface sus necesidades diarias
Cruz Rincón Joséph
Comentado en México el 20 de marzo de 2025
Es sencilla, cumple lo que especifica, no se se mancha y ligera...
Katherine Valle
Comentado en México el 17 de febrero de 2025
Se ve de buen material, cubre perfecto el celular, que es un Motorola g04s
Alberto Peniche Hinojosa
Comentado en México el 30 de junio de 2024
Me gustaris comprar en otros colores . Buenos materiales
José Luis Gómez
Comentado en México el 23 de junio de 2024
Llevo 2 semanas con esta funda y ya comienza a despintarse de las esquinas
JESSICA RUIZ REYES
Comentado en México el 26 de noviembre de 2024
Quedó perfecto, el negro es mate, es ligera y da buena protección.
Aleja
Comentado en México el 31 de octubre de 2024
Muy buena calidad
Customer
Comentado en México el 29 de octubre de 2024
Le queda perfecta al Moto g24, justo el material y fit que andaba buscando
J.W.
Comentado en Canadá el 19 de mayo de 2023
Had it for few months now, seems to work fine. The psi limits were accurate enough. One of them (on or off don't remember which one anymore) was 5psi off, the other was within half a psi of the rating. The one negative is that there is no manual lever for turning it on/off. So if you want to flush out your tank or some other stuff, that'll be more difficult.Edit: 14 months later, still working without issues.
Mark
Comentado en los Estados Unidos el 10 de diciembre de 2023
I purchased this after realizing that there was not anything wrong with what I have. It's good to have on hand in case needed.
Richard
Comentado en Canadá el 11 de agosto de 2021
efficace
Dave Truax
Comentado en Canadá el 6 de julio de 2021
Great
trealmc
Comentado en los Estados Unidos el 28 de noviembre de 2020
wiring the switch for 12v.............or for 120v, or for 240vThe switch is just like a house light switch, meaning your neutrals will go together, and your grounds go together, just wire nut them together and push them inside the cover; and the 4 terminals are only used for the hot wires. There are two sides, left and right, and only both sides are used if you are wiring for 240v because then you have two hot wires in, and two hot wires out. Otherwise, if you are using 120v, you only need to hook up the one side of the terminal. If you are using it for 12v, the same applies, only hook up one side. The hot wires are colored differently for 12v (white), than they are for 120v (black), than they are for 240v (red and black).The water pressure switch works by pushing in from behind the switch to disconnect the connection when it comes to pressure. The terminals are L1/M (that is one side), and M/L2 (and that is the right side).L1 = power source inM = power source out (water pump)M and L2 are only for 240v, and would be L2 power in, and M power out (match the colors)I wired it for 12v, and I could not find a video, or anyone who explain to me how it worked so I knew what I needed to do. Here is how I wired it for 12v.the 4 terminals, from left to rightL1 = white (+) from power sourcem = white (+) to power water pumpm = do not needL2 = do not needthen wire your blacks (-) together with a wire nut and tuck inside cover of switchyour done.*if your wiring it for 120v, then put the black (hot) wires in place of the L1 and M.and wire nut the whites together, and wire nut your grounds together; you do not use M or L2.*if you are wiring for 240v, then put the black (hot) wires on L1 and M, and put your red on M and L2.and wire nut the whites together, and wire nut your grounds together.*the center adjustment is for adjusting the pressure up or down(this is a general main setting, which you need to counterturn until your desired cutin is acheived)(your cutoff adjustment is the smaller adjuster to the upper left)(when you adjust this main adjustment in the middle, it will keep the range the same as you adjust it...which means, if it is 30-50, and you turn it counterclockwise 4 full turns to bring it to 20psi cut in,then it will now be at 20-40. See how it changes the overall range? So your cutout adjustment also changes and stays with the range.)(If you want to dial in the top range cutoff, to raise or lower it, then you use the smaller upper screw in the upper left to do that......AFTER.....you have set the cutin on the range adjustment, the one in the center.)raise it by turning it clockwiselower it by turning it counterclockwiseone full turn will change the psi by 2.5*the smaller adjustment that is offset to the upper left is for the high pressure cut off. Adjust it after you have set the range to your desired low pressure cutin. I believe the adjustments are the same for this screw also, 2.5psi per full turn, clockwise to raise, counter to lower.
Productos recomendados
Mex $149.00
Mex $ 87 .00 Mex $87.00
Mex $149.00
Mex $ 80 .00 Mex $80.00
Mex $291.00
Mex $ 148 .00 Mex $148.00
Mex $149.00
Mex $ 87 .00 Mex $87.00
Mex $491.99
Mex $ 231 .00 Mex $231.00