No hay artículos en el carro
No hay artículos en el carroCuando el termostato pide calor, el control 780-845 inicia simultáneamente chispas de encendido y abre la parte de la válvula piloto de la válvula de gas. El reconocimiento de llama piloto detiene la chispa de encendido y abre la parte principal de la válvula de gas. La llama del quemador piloto se controla continuamente a una frecuencia sincrónica durante la duración del ciclo de calentamiento. Si la llama piloto fallara durante el ciclo de calefacción, el control apagará la válvula principal hasta que se establezca la llama piloto. El control de encendido de bloqueo 780-845 proporciona 90 segundos de chispa, seguido de un retardo de tiempo de 6 minutos (purga) entre intentos de encendido. Después de tres intentos, si no se detecta ninguna llama piloto, el control entra en un período de bloqueo de una hora. Al final del período de bloqueo, si la demanda de calor todavía está presente, la unidad repetirá los tres intentos de encendido.
Customer
Comentado en Canadá el 14 de noviembre de 2024
It was easy to install although I had to drill a few holes on the bracket of the furnace. Just keep track of the wires and where they go.
Gord
Comentado en Canadá el 27 de octubre de 2021
The Robertshaw ignition module worked great and the replacement from a Lennox SP 745 was straight forward. The wire positions are not all in the same spot so you will need to make note of this as you disconnect the old module. The ignition terminal on the Robertshaw is labeled SPARK, this is the only difference for labelling. The screws that came with kit were a bit too short so I used a more suitable length. My furnace now works great again, I am very happy with the product which saved me a lot of money in the end.
Home user
Comentado en los Estados Unidos el 10 de noviembre de 2020
No se pudo cargar el contenido.
Satoko Fox
Comentado en los Estados Unidos el 15 de enero de 2020
I have an old Carrier 58gsc. It would start, sometimes, then stop. Wiggling the wires seemed to help so I decided the springs connector to the lockout/ignition controller LH33WZ512A had worn out. The 6-pin connector on the old controller looked hard to replace so I took a chance and ordered this controller with friendlier looking connectors. I used $7 worth of "disconnect" terminals that came with a crimping tool and it was within my capabilities.Installation notes: I didn't seem to need to hook everything up. 'PV/MV common' and 'Transformer ground' on the new controller were left floating.I connected the sense to the adjacent terminal on the controller as suggested by the instructions. From the old connector to the new controller:Black - groundBlue - Thermostat 24VYellow - Pilot ValveWhite - Main ValveBrown - No connection (This floats at 24V when the furnace is on. I think it has something to do with the old flame sensing mechanism but this controller doesn't seem to need it.)I was really pleased how quickly the furnace started up. Just a few seconds; much quicker than the old controller. Also, when I turned off the gas, the controller immediately locked out until I turned the thermostat down and back up again. Seems safe. Not sure how the flame sensing works; seems like magic; but works. At one point I connected the brown wire to PV which is wrong and the controller LED blinked then shut down which was helpful in guessing the connections.I had paid some con artist $90 to quote me $650 to replace the perfectly good control valve. This box fixed my problem for $80. Great product!
Miranda K Miller
Comentado en los Estados Unidos el 19 de diciembre de 2017
Ran into a problem with our Lennox Whisper G20 last season where it would light, run for a few minutes, then go out before getting up to temperature. Then I took a air compressor with nozzle and blew out the heating element chamber and we were fine the rest of the winter. I didn't think much of it other than when the main burner would first come on, the furnace would making a strange clicking noise. I would assume to hear a clicking noise when igniting the pilot, not when opening the main valve.This year, the clicking noise got even worse. I assume it was the sound of the MAIN VALVE relay in the ignition control. Well, eventually, the house started getting cold and in investigating, found that the furnace would light the pilot, eventually kick on the blower motor, but the main burner never came on and the system would shut down right away. I cleaned the flame sensor rod, tested the flame sensor current (1.8 microamps), but none of those things helped. I found AC voltage when the pilot lit across PV & PV/MV, but never found any voltage across MV & PV/MV. It would never open the main valve (turn on the main burner). I assume the clicking relay in the Robertshaw SP 835 (that it was currently equipped with) finally gave out and that I needed to replace the control. I ordered this on Saturday and received it Tuesday (one-day shipping? My only gripe is that I think one day shipping should mean one day) and as soon as I hooked it up, the furnace worked perfectly. Interesting difference with this model is the tail for the flame sensor which allows you to bypass it. It can be bypassed by plugging the black wire directly into the sense spade. Please don't do this- I wish it weren't equipped with this feature. Make sure the flame sensor is plugged in and the tail (the black wire) is hanging not plugged into anything. Otherwise, it will think the burner is lit, even if lighting fails, and could fill your house with gas.Anyways, so far, so good. If I have any problem with it I will update the review.
Productos recomendados
Mex $1,281.00
Mex $ 640 .00 Mex $640.00
Mex $5,163.90
Mex $ 1,881 .00 Mex $1,881.00
Mex $1,560.06
Mex $ 639 .00 Mex $639.00
Mex $144.19
Mex $ 80 .00 Mex $80.00
Mex $7,871.23
Mex $ 1,881 .00 Mex $1,881.00
Mex $946.55
Mex $ 501 .00 Mex $501.00