No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Los anclajes de amarre son compatibles con múltiples accesorios de posventa, tales como divisores de carga, tacos de amarre y extensores de cama, rampas de carga almacenables y mucho más
Función: anclajes de amarre fabricados con aleación de zinc fundido, con carcasa de plástico pesado y conjunto de bloqueo de acero inoxidable.
Si transportas cualquier tipo de carga, tendrás que asegurarla con algún tipo de amarre - ya sea correas, redes, lonas o cadenas. Y tendrás que fijar tus amarres a los puntos de anclaje en tu camión o remolque. Si no tiene puntos de anclaje o carece de lugares convenientes para fijar amarres, puede agregar puntos de anclaje
Estos anclajes de amarre están hechos de material de zinc fundido a presión, no requieren perforación, fácil de instalar
M. Henderson
Comentado en los Estados Unidos el 16 de febrero de 2025
Nice clean install, fits well, functional while being understated.On the 2025s at least the stake holes are covered with caps that just pop out from the rear of the truck. No need to cut the openings, just pop the caps, angle the bed tie down anchor, hook the side openings and tighten the screws. One of the easier modifications I've made the truck. Probably 10 minute install.Props to Hyundai engineering to make the holes etc the same size as the F150 stake holes.
Skip Webb
Comentado en los Estados Unidos el 16 de febrero de 2025
These went in with no problems. Another purchaser recommended coating the screw- in bolts first with Vasoline on the threads to "cut the threads into the truck body before attempting to install the devices. Great advice! After "pre-threading the bolts first and then taking them back out, the devices installed without issue, and the bolts snugged up into the truck. The keys are "universal" and would only prevent someone without a key from removing them.
Mike Mancini
Comentado en Canadá el 17 de mayo de 2024
Easy to install and fits well. Installed in 30 minutes. Installed on 2020 F-150.
Aaron Kash
Comentado en los Estados Unidos el 25 de marzo de 2023
I was nervous about buying this kit given the negative reviews with shearing screw heads but I decided to try it anyways. I followed advice found in other reviews and I had no issues with installation. If you take your time you should have no worries about a failed installation.I used petroleum jelly on each screw and used my impact driver to tap the holes. I used a fresh screw for each hole and threaded each hole before putting the plate on. No need to drive all the way in when tapping; I went about 2/3 of screw length.With the plate held in place, I put another dab of jelly on the tip of the screw before driving it back in with the impact driver. I didn’t fully seat the screws with the impact driver; however, out of fear of over tightening and breaking a screw off. I the did final seating with small socket wrench equipped with the supplied bit; torquing each screw in an alternating pattern until each was snug. I don’t know what the formal torque specs are for these screws so I went by feel. They seem plenty secure.There is a small amount of play in the cleats once they’re installed and locked. I’d be curious how this compares to Ford OEM. This is my only critique of the set but given the price point (1/3 the cost of an equivalent Ford setup), I find it acceptable and will meet all my needs which are admittedly not heavy duty.Also to note, even though 2022 model year is not listed this kit worked perfectly fine with my 2022 F150 XLT (supercab with 5.5’ bed). The bolt pattern in the bed matched with the plates with no fitment issues whatsoever.
Dany gauthier
Comentado en Canadá el 18 de diciembre de 2023
Fit parfait tacoma 23
Productos recomendados
Mex $339.00
Mex $ 186 .00 Mex $186.00
Mex $702.05
Mex $ 351 .00 Mex $351.00
Mex $159.00
Mex $ 79 .00 Mex $79.00
Mex $1,775.18
Mex $ 745 .00 Mex $745.00
Mex $430.17
Mex $ 219 .00 Mex $219.00