No hay artículos en el carro
No hay artículos en el carroSomos Songle Relé original Tamaño: 70 mm X17 mm X20 mm (LxWxH) - Chip principal: EL817, SRD-DC03V-SL-C - Voltaje de trabajo: DC 3V/3.3V - Control 10A 250VAC, 10A 30VDC Características - Instrucciones con la salida de señal; - Puerto de entrada de señal puede conectar el puerto IO del microcontrolador, señal de alto nivel - SelecselecselecselecselecselecselecselecLa capacidad de interferencia es fuerte, protección de aislamiento fotoeléctrico de alta fiabilidad - Amplio rango de detección actual: entrada DC0-25V - Protección de corriente de diodo - El tiempo de respuesta es inferior a 20 milisegundos - Relé de larga vida puede absorber 100000 veces continuamente - Conexión externa utiliza terminal de engarce giratorio, hace que la conexión sea más firme - Con orificio de instalación fijo, instalación conveniente, disparador de alto nivel: el modo de relé. se triggse se trata trata de por señal de alto nivel, que se puede ingresar desde el microcontrolador IO, tapas de puente: puedes seleccionar si el relé y la señal comparten la misma fuente de alimentación o no quitando las tapas de puente en los pines o no. Se recomienda compartir la misma fuente de alimentación, ya que es más conveniente para usar.
ben
Comentado en los Estados Unidos el 15 de enero de 2025
These don't fit the wires you'd typically use in a Arduino project because they are too small but it's really easy to just desolder the connecter and solder your wires directly.
Anthony C
Comentado en los Estados Unidos el 28 de agosto de 2024
There are a lot of reviews for these clearly written by people using them in ways they are not intended to be used.I am using these to trigger different animatronics from an ESP32. I have 3 of them run in parallel with a 3v LED at the end of the chain. I am powering them from the ESP32's 3V3 pin. I am using a GPIO as the trigger. The ESP32, connected via usb to a computer, still provides enough amperage to trigger all 3 at the same time in addition to powering the LED.The relays support 250V@30A on the output side ONLY. Some people mentioning theirs caught on fire, but clearly are running voltage to the wrong rails.There's no documentation on the jumpers, but basically they are ground and VCC. I am not sure why they would be there, but I guess you could use them as headers to not use the screw terminals? this seems silly though as IN would still need to use the screw terminal.Overall these work great for my project.
Kaushik Ghose
Comentado en los Estados Unidos el 6 de diciembre de 2024
Can be used from a ESP32 system which has 3.3V logic without any additional circuitry. Has screw terminal blocks for both sides of the relay making it easy to integrate with microcontroller board. Has a red LED that lights when the relay is activated, giving good operational feedback.Only niggle is that the screw holes are a bit small. i had to enlarge them with a file to fit normal sized standoff screws.
Exscotticus
Comentado en los Estados Unidos el 27 de octubre de 2024
These relays have a nice skinny form factor and can be attached directly to 3.3V tolerant GPIO.The only negative is that the M2.5 mounting holes are too close to the edges of the board. Hardly any material forms the holes and cracking is a concern.
Godron Smierdzidupa
Comentado en Canadá el 26 de octubre de 2024
They come attached, but are easy to split off individually if needed. They’re working great, controlled by simple GPIO pins from an ESP32 board.
Productos recomendados
Mex $252.13
Mex $ 138 .00 Mex $138.00
Mex $450.74
Mex $ 243 .00 Mex $243.00
Mex $10,705.65
Mex $ 1,881 .00 Mex $1,881.00
Mex $521.55
Mex $ 271 .00 Mex $271.00
Mex $358.48
Mex $ 172 .00 Mex $172.00
Mex $139.16
Mex $ 72 .00 Mex $72.00
Mex $585.45
Mex $ 275 .00 Mex $275.00
Mex $238.00
Mex $ 121 .00 Mex $121.00