No hay artículos en el carro
No hay artículos en el carroTrebor
Comentado en los Estados Unidos el 11 de febrero de 2025
Excellent quality and functionality. I did not use these as their intended purpose, but they exceeded the thermal plans and expectations. I glued these bad boys to the top of the Stock HP VRM Heat Sinks with thermally conductive glue/epoxy. I upgraded an Omen 25L to a Ryzen 9 5950X and obviously pushing the stock HP Hana Board to its limits would cause the VRM’s to over heat and crash the OS with blue screens. Using these as a MOD definitely stabilized the system. Didn’t even need to add additional fans, as the two radiator exhaust fans are close enough to pull air through the pipes and fins. They stay very cool. Excellent design!
350ZMO
Comentado en los Estados Unidos el 30 de julio de 2024
23 June 20241) SAMSUNG 990 PRO SSD NVMe M.2 PCIe Gen4 MZ-V9P2T0B/AMSold by: Amazon.com Services, Inc $169.992) Thermalright HR09 2280 PROSold by: Thermalright Direct $8.993) Noctua NF-A6x25Sold by: Noctua Cooling Solutions $14.95I decided to go ahead and put a heatsink on this. Heat has been, is and shall always be the #1 enemy to electronics. Unfortunately, heat dissipation engineering is often underrated, overlooked and badly done, if done at all. With this setup, it never gets above 30c during Samsung Magician performance test. Base mobo temp is 29C.Before attaching the HR09 I removed the sticker from the drive and removed the silicone pad from the heatsink and applied Prolimatech PK-3 to the heatsink. The picture shows TF-7 but I found that stuff way too thick and didn’t spread well. I used Acetone and q-tips to get the sticker gum off. The bottom of the HR09 is steel and really needs to be aluminum but the chips are on top so that is where the most heat can be dissipated. I then attached an NF-A6x25 to the HR09 using nickel wire.IMHO silicone pads don't work. I tried the new Zezzio 14.8 W/mK Silicone Thermal Pad and temperatures were 32C during the SAMSUNG Magician performance test. Most thermal pads are horrible so I had high hopes for the Zezzio only to have them dashed. Do yourself a favor, scrape off the included pad and apply PK-3 or equivalent. Remember to get the sticker off the M.2 drive as well.Forget spatulas for applying heatsink compound. All heatsinks are a mm or two larger than the item they go on. The HR09 is no exception. Run tape on the very edge down both sides a mm or two. Apply paste and smooth with a single sided razor blade. Then take tape off. the tape will act as runners for the single edged razor blade to skate on. Hold the blade at an angle, not critical, somewhere between 10 and 60 degrees. Perfect complete coverage without bubbles and uniform thickness every single time. Gives immediate visible indication it worked. You will know in an instant if your paste is good or too thick dried out beyond it's shelf life. Apparently I didn't take a picture of this with the HR09 so I'm including one of a CPU heatsink to give you the idea - same exact concept.On it's own without doing these things, it might as well not be there which accounts for those reviews. Also take your time and augment the high density foam between the bottom of the steel plate and the mobo as necessary. I found the included piece to be of insufficient thickness but I found some from other packaging that I could to desired shape and thickness with that signle sided razor blade.I *almost sourced some aluminum U channel of the correct ID to replace the steel bottom bracket and then I thought naaaa. That'd be taking it to far. LOL
Paresh Shivdikar
Comentado en India el 12 de julio de 2024
Great Product very good above image is without AC almost matches my room temrature
JMF
Comentado en los Estados Unidos el 23 de mayo de 2023
This heatsink is great. It looks nice, installs easily, and cools my Samsung 960 Pro SSD to almost room temperature even without any direct airflow through the fins, just slight airflow from the side. As Roman from Der8auer showed, it's one of the few SSD heatsinks that's actually effective. I also really like that it's held on by 4 screws instead of rubber bands or double sided tape like many others, which will likely fall off over time. It's also nice that this heatsink has no directional letters or markings because it will look great regardless of the SSD's orientation.My main concern is although it's not excessively heavy, it's still quite a bit of extra weight hanging from the SSD's slot and tiny mounting screw. I don't think this will be a problem while the computer is stationary, but if you have to ship your computer or move it long distance, removing the drive would be a good idea for safety. Also, be mindful of this heatsink while working in your case because I don't think it would have to be bumped very hard to risk causing damage as long as it is.Unless you just want extreme overkill or you have specific requirements such as running very storage intensive workloads on a drive located somewhere with little airflow, you may want to consider getting the smaller and lighter non PRO version of this heatsink instead.
Sascha
Comentado en Alemania el 10 de mayo de 2023
Okay für alle die sich dafür interessieren kann man empfehlen gekühlt ca.5-10Grad runter je nach Position im System da ein Luftstrom sinnvoll bei diesem Kühlerprinzip ist nicht unbedingt über der Grafikkarte verbauen dort ist kaum eine Kühlleistungsmehrwert erkennbar wanderte deshalb bei mir zum zweiten M.2 Slot unter meiner 4090 wo die Gehäuselüfter von unten Frischluft bringen. Fazit nette Spielerei die die M.2 SSD kühler hält...
Daniel
Comentado en México el 28 de febrero de 2023
ESTABA MUY INCRÉDULO PERO AHORA MI TEMPERATURA NO SUPERA LOS 33 GRADOS Y ESO QUE LA MAQUINA LA UTILIZO 15 HORAS DIARIAS
Luis Castillo
Comentado en México el 11 de febrero de 2023
Realmente no tenía problemas con el enfriamiento, pero quise asegurarme de ello. Este nene baja en 20 grados mi KC3000 (pci express 4, 7tb/s) y eso que ya estaba siendo enfriado por una placa que traía mi tarjeta madre, sin disipación probablemente sería aún más notorio el enfriamiento.La única contra que le pongo es que debe ser montado antes que un disipador grande de aire, o de otra forma será casi imposible de montarlo.
Irwin
Comentado en México el 1 de febrero de 2023
Compre este disipador para mi SN850X, ya que el prender la computadora la temperatura rondaba en los 45° y al usarla sobrepasaba los 60° incluso sin jugar los juegos instalados ahi, ahora al prenderla esta a 27° y usandola con juegos instalados en el M2 dificilmente llega a los 50°, la temperatura promedio de uso sin jugar es 36° lo cual se me hace una temperatura perfecta. Al principio tenia miedo de que no alcanzara el disipador por el tamaño de mi tarjeta grafica y el enfriamiento liquido pero como se puede observar en las fotos apesar de que el disipador es muy grande cabe perfectamente.
Productos recomendados