No hay artículos en el carro
No hay artículos en el carro
Este calentador de descongelación (número de pieza WR51X10055) es para refrigeradores.
Brittany Kirkland
Comentado en los Estados Unidos el 14 de marzo de 2025
Defrost went out and stopped working within less of 2 weeks of use, bought to avoid food spoiling.
Ocie w
Comentado en los Estados Unidos el 25 de enero de 2025
Easy installation, fix perfect
Miguelbetza
Comentado en México el 23 de julio de 2024
Gran producto, me funcionó perfecto, otros los cambiaba y duraban 1 o 2 meses y fallaban, este lleva 6meses y sin problema. Cambien los sensores que trae y de seguro no tendrán problemas.
Francisco Sandoval
Comentado en México el 10 de febrero de 2024
Reemplazo exacto para un refrigerador GE profile.Las bases son de cerámica, lo cual evita que con el calor de la resistencia dure menos.
Bob Stoddard
Comentado en los Estados Unidos el 18 de diciembre de 2024
Easy install, good performance
A. Dimla
Comentado en los Estados Unidos el 8 de noviembre de 2024
It’s hard to beat the price, I replace a failed defrost heater with this unit. Dropped it in and tested for a few cycles, working as normal.
Fan
Comentado en México el 1 de julio de 2023
Adquirí el producto para cambiar la resistencia para descongelar y la resistencia viene con dos piezas adicionales que pueden fallar simultáneamente, funciono muy bien
BlackyChan
Comentado en los Estados Unidos el 14 de agosto de 2022
Works well just follow directions when mixing it though.
jimolson
Comentado en los Estados Unidos el 20 de julio de 2022
9 times out of 10 the only part in this kit needed to get your refrig back on the air is the defrost heater element. The kit comes with a thermostatic switch and a temp sensor, but these parts rarely fail and replacing them requires more disassembly of the refrig.However, the heater element fails frequently. This is the third time in 20 years I've replaced mine. The replacement interval is roughly 5 years, and is indicated by poor cooling in both compartments and a build up of thick frost on the back wall of the freezer compartment.This is the sequence of tasks to replace the burned out heating element:1. Empty the freezer compartment and remove its shelves. Leave your food in the warmer side of the refrig and keep its door closed.2. Manually break up/break off the thick frost that has grown in the rear of the freezer compartment. If the frig is kept off (=de-powered) for an hour or so this is easier to accomplish. By breaking off much of the frost bergs you reduce the amount of water released by task #4 in this list.3. Remove the vertical white sheet metal panel that covers the back of the freezer compartment using a Philips screwdriver.4. Allow the freezer to defrost for several hours. At some point melting will expose the heating element and it can be removed and replaced with the new one. My burned out heating element had turned black and contained water.Don't get carried away with totally defrosting the entire area behind the vertical white panel because you have food in the right compartment that is going bad. You need only defrost the freezer compartment just enough to free up the heating element from its mount.The remainder of the ice will be dealt with decisively by the new heating element once installed.5. Reinstall the white vertical panel, shelves and re-power the frig.FWIW, I noticed that the qty=2 5mm push-on electrical terminals that attach to the ends of the heating element weren't as "grabby" as they should be. At 5 amps these terminals need to squeeze the matching blades in the ends of the heating element with some force. To re-establish the "grabby" force of new push-ons, pinch closed the claws of the push-on terminals with needle nosed pliers.Though I have done this task three times on my GE refrigerator, a newbie with mechanical skills could accomplish the job in 4 hours including thawing time. Actual work done is less than 1/4 of that time.Have fun. I'm eager to see if I can wring another 5 years out of this GE 25 cubic foot side-by-side because its replacement now costs $2k.
pedro jose cerulla gorriz
Comentado en España el 14 de diciembre de 2022
njm
David Howard
Comentado en los Estados Unidos el 7 de marzo de 2021
Not sure why Amazon has "Rate Features" for "warmth" & "sheerness" for film developer. Slightly different work flow than Unicolor but it is a good value for the money. Make sure to follow the increased time for the 1st developer to ensure good results near the end of the developer's life.
Tyler
Comentado en los Estados Unidos el 22 de diciembre de 2021
Great stuff says what it does no more no less, I did accidentally add more water to the blix but everything was okay still.
Stefan Zaluckij
Comentado en Alemania el 1 de abril de 2021
This powder kit made color developing super easy for beginners and also incredible results!
Productos recomendados
Mex $281.00
Mex $ 165 .00 Mex $165.00
Mex $581.11
Mex $ 296 .00 Mex $296.00
Mex $542.54
Mex $ 282 .00 Mex $282.00