No hay artículos en el carro
No hay artículos en el carroCompatible con equipos con puerto de interfaz USB 3.0, como la placa base, caja de disco duro USB, portátil, reproductor multimedia, disco duro externo USB, impresora USB, etc. Características: compacto, cómodo y fácil de usar. Soporta la última versión de USB3.0, también compatible con la versión USB2.01.1. Carcasa de PVC, duradera, flexible y no se rompe fácilmente. Con alta velocidad de 5 Gbps. Fácil de instalar y compatible con la mayoría de fundas con dispositivos USB3.0, conectar y usar. Consejos de instalación: 1. Engancha el borde inferior en el corte mientras sujeta el inserto trapezoidal en un ligero ángulo. 2. Gira el inserto hacia arriba para encajar el clip de retención en la parte superior en la abertura hasta que encaje en su lugar. El paquete incluye: 5 insertos de conector Keystone USB 3.0 (cables USB no están incluidos). Especificaciones: Conector 1: USB3.0 A hembra. Conector 2: USB3.0 A hembra. Color: negro. Notas: el cable USB 3.0 no se puede conectar a un puerto USB 2.0, pero el cable Se puede utilizar en un puerto 3.0. Permite una distancia de 1 pulgada más el conector de cable USB detrás de una placa de pared. Utiliza un adaptador USB 3.0 de ángulo recto para conectar un cable en espacios reducidos. Prueba los cables con el inserto Keystone antes de instalar permanentemente
Ben R.
Comentado en los Estados Unidos el 11 de noviembre de 2024
Work well. Fit into keystone jacks and can be removed easily. Do not fall out. Recommended.
Dad, the engineer
Comentado en los Estados Unidos el 6 de septiembre de 2024
In my infinite wisdom, I decided to clean up my workbench area. Many pounds of filament later, I have a Multiboard setup. I also decided to take a 1U keystone panel and outfit it with HDMI, USB, and Ethernet jacks. I got the BERLAT XIUXIU USB 3.0 Keystone Jack Inserts (5pcs, F-F, Black-5 Pack).The good news is that the jacks work. They are a pretty tight fit in my patch panel, but without any adverse effects. I got some M-M patch cables to make my setup work, and it works well. With a unit cost under $2, I'm happy with the economics of this product. Recommended
Kev
Comentado en los Estados Unidos el 31 de mayo de 2023
Thanks to Giuseppe's comments for identifying this issue and explaining the problem. This connector is a straight through connector and will block USB3 speeds in certain circumstances. I'm using it between a computer and a USB3 hub with a flash drive.Without this connector, I get 442MB/s Read and 370MB Write speed.With the stock connector installed it drops to only 41MB/s Read and 38MB/s Write.I cut some traces and turned it into a cross over connector. With the cross over installed, 442MB/s Read and 370MB write.If you are good a soldering and PCB rework, you can change this to a crossover connector.Warning, this procedure could ruin the connector and destroy attached computers and devices.Follow these instructions at you own risk, I am not liable for any damage caused if you follow the procedure.1. You'll need to cut traces on the bottom (Side with lettering) at pins 5,6,8 and 9 at both connectors.2. Add the following wires:3. Connector 1 Pin 5 to Connector 2 Pin 84. Connector 1 Pin 6 to Connector 2 Pin 95. Connector 1 Pin 8 to Connector 2 Pin 56. Connector 1 Pin 9 to Connector 2 Pin 6You may also want to cut the VBUS trace to prevent back powering devices
Robert Washam
Comentado en los Estados Unidos el 27 de mayo de 2022
Amazon is pretty stupid because it wants you to add a written review of keystone jack inserts which obviously are just keystone jack inserts and there's really not much to review except, they fit.I'm not sure exactly what you would put here so let's just go ahead and say, they fit.
Giuseppe
Comentado en los Estados Unidos el 17 de mayo de 2021
I bought 3 packs of 5 pieces of this product and this is not working how I was thinking it should.I did many tests to be sure what was happening. First I connected an USB Flash Drive directly to the USB 3.0 to check the performance (Picture Test #1). After that, I connected an USB A to USB A cable to my computer in the plug #1 and the plug #2 to the keystone jack to create an extension to connect a device (my idea was to pass this to another room for the wall), this does not work how I was thinking with an external disk, but this work like USB 2.0 with the same USB Flash Drive, the speed was reduced from 240 MB/s to 40 MB/s read and from 59 MB/s to 29 MB/s write.After some days I could undertstand what the problem was.I used an USB A to A and usually these are crossed. I mean, the pin #5 in the plug #1 is connected to pin #8 in the plug #2, pin #6 to pin #7, pin #8 to pin #5 and pin #9 to pin #6 (Picture Table 1). Therefore, if we use this type of cable and this keystone jack to create an extension, the result will be something crossed and will not work to connect USB 3.0 devices, only will work with USB 2.0, because the pins used to USB 2.0 are not crossed (Pin 1 to Pin 4).To have this working we should use an special USB A to USB A cable with VBUS and Data Pair Straight Through (Picture Table 3).In my case I could not find this type of cable here in Amazon, so I had to change the connections directly on the connector. You can see a picture how I crossed the pins to get a direct cable connection. Also, other option is cut the cable and create a direct cable, I think this last it's better for the performance, we can weld the wires and conver these again with aluminum to avoid interferences.After this changes I tested and I can say this work like USB 3.0 (440 MB/s read and 449 MB/s write). I tested with an external M.2 Disk.Would be nice to have this jackstone key crossed to avoid an extra work, however, I could not find a keystone USB A female to USB A female crossed.
Productos recomendados
